Safety requirements for mine car transportation

(1) The corners of the slope fill, the fill sections with large slopes, and the outside of the high-bank roadbed should be provided with guardrails and retaining walls. The night loading and unloading site should have good lighting.

(2) When the dump truck enters the working surface and is loaded, it should stop at 0.5m outside the excavator's tail rotation range to prevent the excavator from slamming and damaging the vehicle.

(3) When loading the vehicle, the engine is not allowed to turn off the fire, the cab door is closed, and the head and arms are not allowed to extend outside the driving room. It is forbidden to inspect and maintain the vehicle.

(4) After loading the vehicle, the driver or commander of the excavator sends a signal to allow the car to exit the loading location.

(5) It is forbidden to use the rolling method to start the vehicle, and it is strictly forbidden to slide in the neutral downhill. When parking on a ramp, the driver cannot leave, he must use the parking brake and take safety measures.

(6) Motor vehicles should drive at medium speed on the roads in the mining area, and speed bends, steep slopes and dangerous sections should be speed-limited.

(7) Under normal operating conditions, vehicles of the same type are strictly prohibited from overtaking, and the vehicles before and after are kept at an appropriate distance.

(8) When foggy weather and smoke are diffuse to affect visibility, the yellow light and the marker light shall be turned on and the vehicle shall be decelerated on the right side. The distance between the front and rear vehicles shall not be less than 30m according to relevant regulations.

(9) When the line of sight is less than 20m, the vehicle should be suspended on the right and the warning light behind the vehicle must not be extinguished.

(10) When the snow and rainy roads are slippery, there should be anti-skid measures and slow down; the front and rear distance should not be less than 40m; it is forbidden to turn sharply, brake, overtake or tow other vehicles.

(11) When driving near a slope or a dangerous road, the car should be carefully passed to prevent the frame from collapsing and falling. It is forbidden to stop for no reason on production trunks and ramps.

(12) of the motor vehicle by the front railway crossing, the driver should slow Liao Wang, confirmed by security before.

(13) The unloading location must be provided with a firm and reliable parking facility, and a special person command. The height of the parking facility shall not be less than 2/5 of the maximum tire diameter of the various transport vehicles at the unloading point.

(14) The car should enter the discharge site to obey the command. After the unloading, the bucket should be lowered in time. It is necessary to confirm that the dumper is behind and can move the car to prevent the dumping from erecting the high-altitude lines and pipelines.

(15) The dump truck should not be allowed to approach when the bucket is raised and lowered. After the unloading work is completed, the manipulator should be placed in the neutral position to prevent the bucket from automatically rising when the vehicle is driving.

(16) Dump trucks are strictly prohibited from carrying flammable or explosive materials; outdoor platforms, pedals and bodies are not allowed to carry people. It is forbidden to lift the bucket during operation.

(17) It is necessary to strengthen the inspection, maintenance and maintenance of motor vehicles to ensure the operation of the motor vehicle and the front and rear lights are normal, and the brakes are sensitive and reliable.

Oilseed Flaking Machine / Oilseed Flaker

flaking machine for soybean cotton seed oil extraction


Introduction:
Flaking machine is mainly made up of two or more opposite rotating rolls (high nickel chrome molybdenum alloy), when fuel material (soybeans, peanuts, seeds, etc.) through two roll by the moment when the extrusion formation of embryo, and the first rolled out the oil, then leaching formed by refining finished cooking oil. Is a typical extrusion equipment.

Mill is a key equipment to vegetable oil processing enterprises pretreatment process, it is to rely on the clamping force between the two roller by granular material extrusion into thin slices of the technological process, the common problems of the previous production of the mill is the rigidity is not good, and roll back down without buffer device.I plant production mill work smoothly, the operation is simple, flexible and reliable performance, and is equipped with buffer device between roll, the roll for collision damage rate to a minimum extent.

Flaking Machine


DingZhou YongSheng Grain and Oil Machinery Co., LTD is a professional company combining research and development design, production and sales as a whole. The company has first-class oil equipment manufacturing base, professional oil technology engineer and professor, possesses advanced production technology and sophisticated equipment, All the mechanical parts are manufactured by our company.

The complete sets of oil equipment that we manufactured, relying on many domestic scientific research institutions. Advanced technology, suitable for making all kinds of plant oil. From the raw material of cleaning up, prepressing, leaching, refining and the production processing of by-product (such as Phospholipids engineering, protein engineering), is totally a dragon design and production, has created considerable economic benefit and social benefit for the user and society more than 40 years. Company new development of biodiesel equipment technology in recent years, has put dozens of sets on the market, obtaining good economical benefits both In the domestic and overseas. At present, we have hundreds of successful installation operation of the oil equipment engineering experience, can design and product according to the difference of the user's economic condition. raw material regional, install oil equipments.

YongSheng comapny with scientific management method, strives for perfection the manufacturing process, innovative manufacturing idea, fast grows and become the grain and oil machinery production and export base in China. Company products are exported to Russia, India, Nepal, Indonesia, South Africa,Tanzania,Ethiopia,Ukraine, kazakhstan, Pakistan, Iran, north Korea, Vietnam, France and the European Union and so on more than 30 countries and area.


Vegetable Oil Extraction Machine,Oil Extraction Machine,Oilseeds Flaking Machine,Cooking Oil Machine

Hebei Huipin Machinery Co.,LTD , https://www.oilpresschina.com

This entry was posted in on